Heat pump or furnace? That is the first thing that matters when the heat quits in Aurora, CO, because the two fail in completely different ways. Heat pumps tend to freeze up when defrost stops working, get stuck in cooling when a reversing valve fails, or quietly lean on the electric backup strips, at several times the normal operating cost, when the outdoor unit dies. Gas furnaces usually come down to the flame sensor: once oxide coats it, the burners light but the flame cannot be proven, so the board cuts the gas and locks out after three tries. After that, we most often find cracked hot surface igniters, stuck pressure switches, clogged condensate traps on high-efficiency models, and blower motors at the end of their life.
Aurora HVAC runs every no-heat call diagnosis-first. Our experienced technicians read the board's fault codes and then verify them, measuring flame signal in microamps, testing igniters for resistance, confirming pressure switch operation against actual inducer draft, metering capacitors and motors, and checking refrigerant charge and defrost operation on heat pumps. Gas-side visits include the safety fundamentals as standard practice: we leak-test connections, inspect the heat exchanger, and verify venting, because a heating repair that is not verified safe is not finished.
We service every common heating system type across all major brands, with igniters, flame sensors, capacitors, inducer motors, and blower motors stocked on the truck, so most homes have heat again the same visit. If your equipment is at the end of the road, we say so honestly and walk you through the options with real numbers. For fast heating repair anywhere in Aurora, call (970) 602-4904 and we will get the warm air moving today.
The repair homeowners call us about most is Furnace Repair in Aurora. Start there if your system isn't running right.
Signs You Need Heating Repair in Aurora
Recognizing the warning signs early can save you time, money, and prevent significant damage to your property. These are the signals our technicians see most often when a problem is underway:
- A loud boom when the burners light, which points to delayed ignition
- Thick ice or frost covering the heat pump outside
- A rotten-egg, burning, or musty smell once the heat kicks on
- Cold rooms in one part of the house while others are comfortable
- Higher heating bills with less comfort to show for them
- No warm air at the registers even with the heat turned up
- Clicking and failed ignition attempts before the furnace gives up
- The system starting and stopping every few minutes without warming the house
Early Action Saves Money
What seems like a minor issue today can take out a compressor or heat exchanger tomorrow. Don't wait, get Aurora HVAC on the phone at (970) 602-4904 and we'll take a look right away.
Ready to Solve Your Heating Repair Problem?
Call our expert team for pricing today.
Call (970) 602-4904 TodayYour Heating Repair Questions Answered
Why Hire a Professional for Heating Repair?
Combustion is what makes heating repair different from the rest of home comfort work. A late light-off booms unburned gas inside the heat exchanger and stresses the metal each time it happens. A cracked exchanger can leak combustion gases into the air your family breathes, and a flue that stops drafting pushes carbon monoxide into the living space instead of outdoors. None of these problems make themselves obvious to someone without training and instruments. Diagnosis has its own traps as well. Short cycling can point to a failing limit switch or to a furnace protecting itself from a clogged filter, and cleaning a fouled flame sensor without asking why simply sets up the next lockout.
That is why Aurora HVAC does not guess. Our technicians read flame signal on a meter, look at the heat exchanger directly, confirm the flue is drafting, and compare temperature rise to the data plate so the blower and the fire are properly matched. On heat pumps we check defrost controls, sensors, and the reversing valve before blaming the compressor, and we find out whether the electric backup heat has been running in the background and driving up your costs. Nothing is called fixed until it has run a full cycle and proven itself safe and correct, because your family's warmth and safety depend on it.
Our Heating Repair Process
We work through a clear, repeatable process so nothing gets overlooked on your property. Here's what you can expect when you choose Aurora HVAC:
Testing & Safety Check
Fault codes are only the starting point. We measure flame signal and igniter resistance, test the pressure switch, check motors and capacitors, verify charge and defrost on heat pumps, and leak-test the gas connections on every visit.
Clear Findings & Upfront Quote
We show you what failed and why, and give a firm price before work begins. If a cracked heat exchanger or dead compressor changes the math toward replacement, we say so plainly.
Expert Repair
Igniters, flame sensors, pressure switches, capacitors, and motors ride on our trucks, so most heating repairs are completed the same visit and the house starts warming before we leave.
Complete System Check
A repair is not done until the system proves itself. That means full cycles, temperature rise checked against the data plate, combustion and draft confirmed on gas equipment, and every safety control verified.
Maintenance Tips for Heating Repair
Smart maintenance is almost always cheaper and easier than an early replacement. Follow these tips from our experienced technicians:
- Take booming ignition or new rattles seriously; both are cheap to fix early and expensive late
- Test carbon monoxide detectors monthly and put one on every level of the home
- Schedule a professional tune-up every fall before the first cold snap finds the weak parts
- Give the outdoor heat pump unit open space, free of snow drifts and plantings, so it can defrost
- Keep chlorine products, paints, and solvents away from the furnace, because their fumes corrode burners
- Leave open space around the furnace so the burners can draw enough combustion air
- Replace filters monthly through the heating season to keep airflow strong and the heat exchanger from overheating
Should You DIY or Call a Pro?
Some simple checks are suitable for DIY, but most heating and cooling repairs benefit from professional tools, training, and experience. Consider the following comparison:
| Factor | DIY Attempt | Professional Service |
|---|---|---|
| CO Safety | No way to detect a CO problem | Heat exchanger and draft verified |
| Diagnosis | Error code guessing games | Every component tested with a meter |
| Gas Safety | Fittings tightened and trusted | Every joint checked with a leak detector |
| Heat Pump Faults | Defrost faults mistaken for dead units | Boards, sensors, and valves tested properly |
| Underlying Cause | Quick fix, same failure next week | The reason it failed tracked down |
| Final Testing | Called fixed after a single cycle | Temperature rise measured over full cycles |
Talk to a Heating Repair Expert
The sooner you call, the sooner your comfort is back. Reach Aurora HVAC for fast service.
Get Help: (970) 602-4904Areas We Serve for Heating Repair
We serve Aurora and its neighboring communities for heating repair, from quick same-day repairs to planned installs.